Design of an active helicopter control experiment at the Princeton Rotorcraft Dynamics Laboratory

In an effort to develop an active control technique for reducing helicopter vibrations stemming from the main rotor system, a helicopter model was designed and tested at the Princeton Rotorcraft Dynamics Laboratory (PRDL). A description of this facility, including its latest data acquisition upgrade, are given. The design procedures for the test model and its Froude scaled rotor system are also discussed. The approach for performing active control is based on the idea that rotor states can be identified by instrumenting the rotor blades. Using this knowledge, Individual Blade Control (IBC) or Higher Harmonic Control (HHC) pitch input commands may be used to impact on rotor dynamics in such a way as to reduce rotor vibrations. Discussed here is an instrumentation configuration utilizing miniature accelerometers to measure and estimate first and second out-of-plane bending mode positions and velocities. To verify this technique, the model was tested, and resulting data were used to estimate rotor states as well as flap and bending coefficients, procedures for which are discussed. Overall results show that a cost- and time-effective method for building a useful test model for future active control experiments was developed. With some fine-tuning or slight adjustments in sensor configuration, prospects for obtaining good state estimates look promising

Coupled rotor-body equations of motion hover flight

A set of linearized equations of motion to predict the linearized dynamic response of a single rotor helicopter in a hover trim condition to cyclic pitch control inputs is described. The equations of motion assume four fuselage degrees of freedom: lateral and longitudinal translation, roll angle, pitch angle: four rotor degrees of freedom: flapping (lateral and longitudinal tilt of the tip path plane), lagging (lateral and longitudinal displacement of the rotor plane center of mass); and dynamic inflow (harmonic components). These ten degrees of freedom correspond to a system with eighteen dynamic states. In addition to examination of the full system dynamics, the computer code supplied with this report permits the examination of various reduced order models. The code is presented in a specific form such that the dynamic response of a helicopter in flight can be investigated. With minor modifications to the code the dynamics of a rotor mounted on a flexible support can also be studied

High-speed data acquisition for the Princeton University Dynamic Model Track

Real time analysis of data can reduce the time involved in exploring dynamic systems. The failure of the data acquisition system at the Princeton Dynamic Model Track prompted its replacement with a real time data acquisition system. Data can be obtained from an experiment and analyzed during and immediately following a data run. The new system employs high speed analog to digital conversion and a small computer to collect data. Sampling rates of 1000 hertz over 44 channels (44,000 words/sec) are obtainable. The data can be accessed as it enters the computer's environment where it may be displayed or stored for later processing. The system was tested on a helicopter rotor steep descent experiment. The data collected compares with previous data from a similar experiment

The design, testing and evaluation of the MIT individual-blade-control system as applied to gust alleviation for helicopters

A type of active control for helicopters was designed and tested on a four foot diameter model rotor. A single blade was individually controlled in pitch in the rotating frame over a wide range of frequencies by electromechanical means. By utilizing a tip mounted accelerometer as a sensor in the feedback path, significant reductions in blade flapping response to gust were achieved at the gust excitation frequency as well as at super and subharmonics of rotor speed

Periodic control of the individual-blade-control helicopter rotor

Results of an investigation into methods of controller design for an individual helicopter rotor blade in the high forward-flight speed regime are described. This operating condition poses a unique control problem in that the perturbation equations of motion are linear with coefficients that vary periodically with time. The design of a control law was based on extensions to modern multivariate synthesis techniques and incorporated a novel approach to the reconstruction of the missing system state variables. The controller was tested on both an electronic analog computer simulation of the out-of-plane flapping dynamics, and on a four foot diameter single-bladed model helicopter rotor in the M.I.T. 5x7 subsonic wind tunnel at high levels of advance ratio. It is shown that modal control using the IBC concept is possible over a large range of advance ratios with only a modest amount of computational power required

Design and numerical evaluation of full-authority flight control systems for conventional and thruster-augmented helicopters employed in NOE operations

The development and methodology is presented for development of full-authority implicit model-following and explicit model-following optimal controllers for use on helicopters operating in the Nap-of-the Earth (NOE) environment. Pole placement, input-output frequency response, and step input response were used to evaluate handling qualities performance. The pilot was equipped with velocity-command inputs. A mathematical/computational trajectory optimization method was employed to evaluate the ability of each controller to fly NOE maneuvers. The method determines the optimal swashplate and thruster input histories from the helicopter's dynamics and the prescribed geometry and desired flying qualities of the maneuver. Three maneuvers were investigated for both the implicit and explicit controllers with and without auxiliary propulsion installed: pop-up/dash/descent, bob-up at 40 knots, and glideslope. The explicit controller proved to be superior to the implicit controller in performance and ease of design

High-Temperature Smart Structures for Engine Noise Reduction and Performance Enhancement

One of key NASA goals is to develop and integrate noise reduction technology to enable unrestricted air transportation service to all communities. One of the technical priorities of this activity has been to account for and reduce noise via propulsion/airframe interactions, identifying advanced concepts to be integrated with the airframe to mitigate these noise-producing mechanisms. An adaptive geometry chevron using embedded smart structures technology offers the possibility of maximizing engine performance while retaining and possibly enhancing the favorable noise characteristics of current designs. New high-temperature shape memory alloy (HTSMA) materials technology enables the devices to operate in both low-temperature (fan) and high-temperature (core) exhaust flows. Chevron-equipped engines have demonstrated reduced noise in testing and operational use. It is desirable to have the noise benefits of chevrons in takeoff/landing conditions, but have them deployed into a minimum drag position for cruise flight. The central feature of the innovation was building on rapidly maturing HTSMA technology to implement a next-generation aircraft noise mitigation system centered on adaptive chevron flow control surfaces. In general, SMA-actuated devices have the potential to enhance the demonstrated noise reduction effectiveness of chevron systems while eliminating the associated performance penalty. The use of structurally integrated smart devices will minimize the mechanical and subsystem complexity of this implementation. The central innovations of the effort entail the modification of prior chevron designs to include a small cut that relaxes structural stiffness without compromising the desired flow characteristics over the surface; the reorientation of SMA actuation devices to apply forces to deflect the chevron tip, exploiting this relaxed stiffness; and the use of high-temperature SMA (HTSMA) materials to enable operation in the demanding core chevron environment. The overall conclusion of these design studies was that the cut chevron concept is a critical enabling step in bringing the variable geometry core chevron within reach. The presence of the cut may be aerodynamically undesirable in some respects, but it is present only when the chevron is not immersed in the core jet exhaust. When deployed, the gap closes as the chevron tip enters the high-speed, high-temperature core stream. Aeroacoustic testing and flow visualization support the contention that this cut is inconsequential to chevron performance